1) Lattice-Boltzmann modeling of gas transport in Ni-Yttria-stabilized zirconia anodes during thermal cycling based on X-ray computed tomography , Electrochimica Acta , 2014年1 , 121,386-393（2014）
2) Quantitative analysis of micro structural and conductivity evolution of Ni-YSZ anodes during thermal cycling based on nano-computed tomography , J.Power Source , , 196,10601-10605(2011)
3) Analysis of the three-dimensional microstructure of a solid-oxide fuel cell anode using nano X-ray tomography , J Power Source , 2011 , 196:1915-1919
4) Auxiliary drying to prevent pattern collapse in high aspect ratio nanostructures , Nanotechnology , , 2011
5) The study of there constructed three-dimensional structure of a solid-oxide fuel-cell cathode by X-ray nanotomography. , J of Synchrotron Radiatio , 2010 , 17,p782
6) 3D visualization of subcellular structures of Schizosaccharomyces pombe by hard X-ray tomography , J. of Microscopy , 2010 , 240, p14
7) Schizosaccharomyces pombe, by full-field transmission X-ray microscopy at 5.4 keV , Anal Bioanal Chem , 2010 , 397,p2117
8) Quantitative study of interior nanostructure in hollow zinc oxide particles on the basis of nondestructive x-ray nanotomography , Appl. Phys. Leet , 2009 , 95, p053180
9) Three-dimensional imaging of a complex concaved cuboctahedron copper sulfide crytal by x-ray nanotomography , Appl. Phys. Lett. , 2008 , 92, p233104
10) A method of gap control based on the principle of equal thickness interference for HARNS fabrication , Microsyst. Technol. , 2011 , 17:101–107
11)  High resolution hard x-ray microscope on a second generation synchrotron source. Review Scientific Instruments , Review Scientific Instruments , 2008 , 79,p103708
12) Study of the demoldingprocess—implications for thermal stress, adhesion and friction control , J. Micromech. Microeng. , 2007年 , 17, pp9-19
13) The comparison of hair from gastric cancer patients and from healthy persons studied by infrared microspectroscopy and imaging using synchrotronr radiation , Caner Epidemiology , 2010 , 34, p435
14) Study of Hot Embossing Using Nickel and Ni-PTFE LIGA Mold Inserts , J. MEMS. , 2007年 , 16,pp411-415
15) Analysis of the demolding forces during hot embossing, Microsystem , Microsystem Technologies , 2007年 , 2007年第13期
16) An Innovative Microelectrode Fabrication Using Photoliography for Measuring Dissolved Oxygen Distributions in Aerobic Granules. , Environ. Scie Technol. , 2007年 , 2007年第41期
17) Investigation on overplating high-aspect-ration microstructure , SPIE , 2006 , 2006
18) Fabrication of X-ray imaging zone plates by e-beam and X-ray lithography , Microsyst. Technol. , 2010 , 16,p1315
19) Fabrication of 3D Photonic Crystal by deep x-ray lithography , SPIE , 2006 , 2006
20) Simultaneous Determination of Nitrate and Dissolved Oxygen under Neutral Conditions Using a Novel Silver-Deposited Gold Microelectrode , Eviron. Sci. Technol. , 2008 , 42,pp8465-8470
21) The properties of demoulding of Ni and Ni-PTFE moulding inserts , Sensors and Actuators A , 200502 , 2005年第2期
22) The compere of Lifetime of Ni and Ni-PTFE moulding inserts with high aspect-ratio structure , Microsystem Technologies , 2005 , 2005年第4/5期
23) Simulation of deep Uv-lithegrugphy iwth su-8 resist by using 365 light source , Microsystem Technologies , 2005 , 2005年第4/5期